EN 388 Glove Ratings Explained (4X42C)
Every protective glove sold in Europe carries a small pictogram with a code underneath — something like 4X42C. That code is the EN 388 rating, and it tells you exactly how the glove performed in six laboratory tests. This guide shows you how to read it, what each number means, and how to match a rating to the job.
How to read the code
EN 388:2016 is the European standard for gloves that protect against mechanical risks. The mark shows up to six characters, one for each test, in a fixed order:
- Abrasion resistance — level 1 to 4
- Cut resistance, Coup test — level 1 to 5
- Tear resistance — level 1 to 4
- Puncture resistance — level 1 to 4
- Cut resistance, ISO 13997 (TDM) test — level A to F
- Impact protection — P if it passes
The letter X means the test was not performed or does not apply. So 4X42C is read as: abrasion 4, Coup cut not tested, tear 4, puncture 2, ISO cut C, and no impact rating.
What each test measures
| Test | What it measures | Levels |
|---|---|---|
| Abrasion | How many rubs the material survives | 1–4 (100 / 500 / 2,000 / 8,000 cycles) |
| Coup cut | Resistance to a rotating circular blade | 1–5 (index 1.2 / 2.5 / 5.0 / 10.0 / 20.0) |
| Tear | Force needed to tear the material | 1–4 (10 / 25 / 50 / 75 N) |
| Puncture | Force needed to push a point through | 1–4 (20 / 60 / 100 / 150 N) |
| ISO cut (TDM) | Force needed for a straight blade to cut through | A–F (2 / 5 / 10 / 15 / 22 / 30 N) |
| Impact | Protection against knocks to the back of the hand | P = passes |
Note the two cut tests: the Coup test is the older method, and it can blunt on high-performance fibres, which is why the newer ISO test exists. When a glove scores X on the Coup test, check the ISO letter — that is the meaningful cut figure.
Worked example: 4X42C
The Ansell HyFlex 11-561 is rated EN 388 4X42C. Decoded: abrasion level 4 — the highest, at 8,000 cycles, so the palm stands up to hard, repeated handling; Coup cut X — not tested, because the ISO test gives the cut result; tear level 4 — 75 N, the highest; puncture level 2 — 60 N; ISO cut level C — 10 N, a solid mid-to-high cut resistance. There is no impact rating, so this glove does not claim knuckle protection. The 11-561 pairs that rating with a 15-gauge liner and a nitrile palm coating, which is why it suits metal handling and assembly work where grip and cut protection matter together.
Matching a rating to the job
Start from the hazard, not from the highest numbers:
- Handling sheet metal, glass or sharp-edged parts: look for a high ISO cut level (C to F).
- Warehouse and general handling: abrasion 3 or 4 with a good grip matters more than maximum cut.
- Work with nails, wire or rough timber: check tear and puncture as well as cut.
- Fine assembly: a thinner, high-cut liner keeps dexterity — a thick glove with a top rating is no good if the worker takes it off to do the job.
Cut resistance is only one part of the picture. Grip, dexterity and comfort decide whether the glove is actually worn, and chemical or heat protection is covered by different standards altogether (EN 374 for chemicals, EN 407 for heat). Browse the range in our safety gloves category or the Ansell brand page.
Mistakes buyers make
- Reading only the first digit. A 4 at the front says nothing about cut resistance.
- Assuming higher is always better. The toughest glove is often the stiffest — if workers remove it, protection is zero.
- Ignoring size and fit. A glove that is too loose reduces grip and control; too tight, and it tears and tires the hand.
- Treating the rating as a guarantee. EN 388 is a laboratory test on new gloves. Real gloves wear, and a worn glove no longer performs at its rated level — inspect and replace them.
Need a quotation? Tell us the product, the quantity and the destination country, and we will come back with a clear price. Send an inquiry or message us on WhatsApp.
Frequently asked questions
- What does the EN 388 rating 4X42C mean?
- It is read as: abrasion level 4, Coup cut not tested (X), tear level 4, puncture level 2, ISO cut level C, and no impact rating. The Ansell HyFlex 11-561 carries this rating: abrasion 4 at 8,000 cycles, tear 4 at 75 N, puncture 2 at 60 N, and ISO cut C at 10 N.
- What does the letter X mean in an EN 388 code?
- X means the test was not performed or does not apply. When a glove scores X on the Coup cut test, check the ISO letter — that is the meaningful cut figure, because the Coup test can blunt on high-performance fibres.
- Is a higher EN 388 rating always better?
- No. The toughest glove is often the stiffest — if workers remove it to do the job, protection is zero. Start from the hazard, not from the highest numbers, and remember that grip, dexterity and comfort decide whether the glove is actually worn.
- Does EN 388 cover chemical or heat protection?
- No. EN 388 covers mechanical risks only. Chemical protection is covered by EN 374 and heat protection by EN 407 — different standards altogether.
